Insights

Engineering and compliance notes for the people who specify, finance and buy utility-scale modules.

Technology · November 2026 · 4 min · Solarix engineering

Heterojunction on a hot site: what the temperature coefficient is worth

Module power falls as cells heat up. The temperature coefficient sets how fast, and the gap between cell technologies is large enough to show up in an energy model.

Every module datasheet lists a power temperature coefficient: the percentage of rated power lost for each degree Celsius the cell runs above 25 °C cell temperature, part of standard test conditions (1,000 W/m², 25 °C, AM1.5). In operation on a hot afternoon, cells run well above that temperature.

The arithmetic

To a first approximation, loss is the coefficient multiplied by the temperature rise. At a cell temperature of 65 °C, 40 °C above standard test conditions, the median values from Kiwa PVEL’s 2026 PV Module Reliability Scorecard work out as follows:

Cell technologyMedian coefficientPower lost at 65 °C
Heterojunction−0.26%/°C−10.4%
Back contact−0.27%/°C−10.8%
TOPCon−0.29%/°C−11.6%
PERC−0.32%/°C−12.8%

The difference between heterojunction and TOPCon at that operating point is 1.2 percentage points of output. Across the hottest hours of a year, an energy model accumulates that difference.

What to check

Medians describe a category, not a product. Kiwa PVEL notes that its heterojunction and back-contact samples are significantly smaller than its TOPCon and PERC samples. For a specific project, use the PAN file for the exact module, ideally one produced from independent laboratory measurements, and model it against the site’s irradiance and temperature data.

Source: Kiwa PVEL, 2026 PV Module Reliability Scorecard, PAN test medians for bills of materials produced 2023–2025. Industry data, not Solarix product results.

Compliance · November 2026 · 5 min · Solarix engineering

Foreign-entity rules in 2026: what to ask a module supplier for

For projects beginning construction after December 31, 2025, the Section 45Y and 48E credits depend in part on where component cost comes from. Here is the document set to request.

The One Big Beautiful Bill Act, signed July 4, 2025, bars “prohibited foreign entities” from the clean electricity credits and adds a material assistance test for projects. The covered nations are China, Russia, Iran and North Korea. A prohibited foreign entity is a specified foreign entity or a foreign-influenced entity (26 U.S.C. §7701(a)(51)). Specified foreign entities include entities on certain U.S. government lists and foreign-controlled entities: the governments of those countries, their citizens or nationals, entities organized there or with their principal place of business there, and entities more than 50% controlled by any of them. Foreign-influenced entities include those in which a specified foreign entity can appoint a covered officer, owns at least 25% (or several own at least 40% together), or holds, alone or with other specified foreign entities, at least 15% of its debt, plus certain entities whose payments give a specified foreign entity effective control.

The material assistance cost ratio

The ratio is the share of a facility’s manufactured-product direct costs not attributable to prohibited foreign entities. The minimum is 40% for qualified facilities beginning construction in 2026, rising five points a year to 60% for 2030 and later. IRS Notice 2026-15 (February 12, 2026) gives interim guidance, including three interim safe harbors: identification, cost percentage and supplier certification. As of November 2026, Treasury had not issued the safe-harbor tables or proposed regulations that Notice 2026-15 anticipates.

What to ask the supplier for

  • A supplier certification for the manufactured products and components supplied, in the form described in Notice 2026-15.
  • Component-level cost data for the module bill of materials, by supplier and country.
  • Domestic content cost data in the format of the elective safe-harbor tables in Notice 2025-08, if you are claiming the bonus.
  • Chain-of-custody records sufficient for U.S. Customs review under the Uyghur Forced Labor Prevention Act.

Construction-start timing matters as well. Under the 2025 law, a solar facility generally qualifies for 45Y or 48E only if construction began by July 4, 2026, or the facility is placed in service by December 31, 2027. On June 6, 2026, a federal district court vacated IRS Notice 2025-42, which had removed the 5% safe harbor for beginning construction on solar facilities above 1.5 MWac. Status as of November 2026; consult counsel.

Orientation only, not tax advice. Your tax counsel determines eligibility. Sources: Pub. L. 119-21; 26 U.S.C. §7701(a)(51); IRS Notice 2026-15; IRS Notice 2025-08; Oregon Environmental Council v. IRS (D.D.C.).

Engineering · November 2026 · 4 min · Solarix engineering

Bifaciality is a system number

A module’s bifaciality factor tells you how well its rear side converts light. How much light reaches the rear is decided by the site.

Bifaciality is the ratio of a module’s rear-side to front-side maximum power, each measured at standard test conditions. It is a property of the cell and module. To a first approximation, rear-side gain in the field is that factor multiplied by the ratio of rear to front irradiance.

A worked example

If rear irradiance on a site averages 10% of front irradiance, a module with 86.2% bifaciality, the 2026 Kiwa PVEL median for heterojunction, gains about 8.6% before mismatch and shading losses. A module at the TOPCon median of 76.5% gains about 7.7% on the same site.

What drives rear irradiance

  • Ground reflectance: light-colored gravel, sand or snow reflects more than vegetation or dark soil.
  • Mounting height and row spacing: higher modules and wider rows let more reflected light reach the rear.
  • Structure shading: torque tubes and racking behind the module block part of the rear side.

For financing, the bifaciality value in the PAN file matters more than the datasheet headline. Independent laboratory measurements on the exact bill of materials give lenders and independent engineers a stronger basis than datasheet values.

Source: Kiwa PVEL, 2026 PV Module Reliability Scorecard, PAN test medians. Industry data, not Solarix product results.