Technology
Utility ULTRA HJT uses heterojunction cells: a crystalline silicon wafer between ultra-thin layers of amorphous silicon. Both faces carry a transparent conductive layer and a fine metal grid instead of an opaque metal back, so the cell can convert light reaching either face. In Kiwa PVEL's 2026 Scorecard PAN testing, HJT had the best median power temperature coefficient of the four cell types tested: −0.26%/°C.
Amorphous silicon passivates both surfaces of an n-type crystalline wafer. Transparent conductors and a fine metal grid on each face carry the current out.
Because the rear face also has a transparent contact and an open grid, light reaching the rear of the module — reflected from the ground — is converted too.
Two calculations an energy model runs on every hour of the year: power lost when cells run hot, and power gained from light reaching the rear.
| Cell technology | Power lost at 65 °C cell temperature | Rear-side gain per 10% rear irradiance |
|---|---|---|
| HJT | −10.4% | +8.6% |
| Back contact | −10.8% | +7.1% |
| TOPCon | −11.6% | +7.7% |
| PERC | −12.8% | +7.0% |
Worked example using Kiwa PVEL 2026 Scorecard medians (industry data, not Solarix results). First-order estimate: loss = temperature coefficient × (65 °C − 25 °C cell temperature), excluding irradiance, spectral and soiling effects. Gain = bifaciality × 10% rear irradiance, before mismatch and shading losses. Your PAN file and site model govern.
Elevated, open rear exposure lets reflected light reach the back of the module. Designed for fixed-tilt and single-axis tracker projects.
Light-colored ground, sand, gravel or snow reflects more light to the rear face.
A smaller (less negative) temperature coefficient means less output lost as module temperature rises.
Bifacial, dual-glass heterojunction module, up to 725 W.
Research direction
Heterojunction cells are a common base for tandem research; In 2023 Oxford PV reported a Fraunhofer ISE–certified 28.6% efficiency on a commercial-size perovskite-on-silicon tandem cell built on a silicon heterojunction bottom cell. Not a Solarix product.
Industry roadmap · ITRPV 17th Edition
The International Technology Roadmap for Photovoltaics surveys manufacturers, suppliers and research institutes each year. Its 2036 projections have heterojunction, TOPCon and back-contact modules all gaining efficiency, with silicon-based tandem modules projected at 27.4% in 2028 and 31% in 2036.
Solar Technology Outlook 2030Average mass-production module efficiency
Silicon-based tandem modules, by the same survey: 27.4% in 2028 and 31% in 2036 (projections).
Independent testing shows higher median bifaciality and a smaller (less negative) temperature coefficient for HJT. TOPCon shares many process steps with PERC, so existing PERC lines can often be upgraded. Heterojunction uses a different, low-temperature process and needs a dedicated line, which is what we built.
ITRPV put 2025 HJT silver use at about 12 mg/W, against about 10 mg/W for TOPCon, and projects HJT falling below TOPCon within the next decade.
Data sheets are on the Documents page; PAN and OND files and test reports are available on request.
Solarix's technical team, led by CTO Napoli Gomez, has worked on heterojunction cell and process development; its CTO and COO have worked together on heterojunction since 2014.
Kiwa PVEL has reported higher median UV-induced power loss for HJT than for TOPCon or PERC, with wide variation by bill of materials. In its 2026 Scorecard, UV-induced degradation became a Top Performer test category and the median TOPCon loss fell to 3.0%. Utility ULTRA HJT uses dual-glass construction.